Top 10 typical forklift crashes ， forklift procedure must focus on these issues ！.

Top 10 typical forklift crashes ， forklift procedure must focus on these issues ！.

Blog Article

Don't ignore the forklift at the workplace. If the operation is not good, there will be severe crashes in mins, and there are several crashes entailing forklifts.

Instance 1: The forklift freight obstructed the motorist's view, and the person in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight goes beyond the permitted width of the route and hangs on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding and surrender during a turn.
Case 5: The forklift driver did not notice the pedestrian, and the pedestrian did not see the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift motorist does not wear the seat belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety and security of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the vehicle driver must initially verify that the lots is steady and reliable.
4. The begin must be sluggish and steady.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole ought to be slanted in reverse. .
2. Do not lift the fork expensive when driving. When entering and leaving the task website or while driving, be careful that there will certainly be no barriers in the sky. When the tons is taking a trip, the fork must not be increased expensive, which will impact the security of the forklift. .
3. After dumping, the fork ought to be reduced to the regular driving position before driving. .
4. When turning, if there are pedestrians or lorries close by, the driving signal should be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the automobile to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it needs to comply with the website traffic rules in the manufacturing facility and have to maintain a certain safety distance from the vehicle in front. .
7. When the forklift is running, the load should be in the lowest position that does not impede the driving, and the gantry ought to be correctly tilted back. The load shall not be raised except when piling or filling. .
8. The elevation of the lots need to not obstruct the motorist's sight. In special situations, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for workers to base on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be fixed and reported in a timely fashion, and they will never run with diseases or conceal them.

filling and discharging.
1. When fork-loading items, the range between the two forks need to be changed as required to make the tons of the two forks well balanced and not skewed, and one side of the item must be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special conditions, security indication need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The speed of the automobile ought to be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it ought to be kept in mind that the fork tip must not touch various other goods or items. The load ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not glide backwards. The pole can be slanted forward somewhat when the lots is lowered to enable simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at high speed and ram difficult things with the fork head. .
7. When the forklift is working, it is forbidden for people to loaf the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to unload the goods or lower the fork frame.
2. Draw the parking brake handle to dead or depress the parking brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance must be inspected, and fuel, lubricating oil and cooling water should be included.
2. Inspect the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature level are regular.
5. After the forklift is running, the outside leakage should additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to examine before leaving the vehicle;.
2. When you encounter a Electric Forklift Truck for Warehouse person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free switching";.
6. Running up and down the slope must be slow and consistent, and no turning on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry must be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the turning around exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not Stand-on Electric Pallet Stacker allowed to utilize stopping pressure to exile round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roads, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the area with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844